Parquet flooring

Andy Barrett

7 years ago

Who is the manufacturer and what is the colour of the wood of the parquet floor? Thanks

Gallery · More Info

Sort by:Oldest

Comment (1)

PRO
AMARI
7 years ago
It's from: http://pietrawoodandstone.com/

Jumbo engineered parquet with a lime wash finish I believe.

Speak with Matthew: 02076106111

The project was 53 Holland Park.

Best

Rob
Related Discussions
Opepe parquet floor
Q
Comments (9)
I don’t think you’ll get the floor to lighten up to match the newer parquet. Convince hubby to go for a darker stain ;-) I’d personally stain and finish with an oil as it’s easier to reapply than a varnish. Osmo oil are pretty good. They do hardwearing oil/wax floor finishes in a range of colours and finishes.
...See More
Which direction should I lay parquet floor
Q
Comments (34)
Taken me sometime as just wanted to exhale and enjoy the moment. Very long post sorry. Preparation Research the job - there are loads of videos on You Tube of what to do and how best to do it; I somewhat took the best from all. Buy more than needed as it's easier to take excess back rather than fall short. Blocks 1. Blocks no longer need to have all the bitumen taken off. There are now adhesives that can do the job without all the scraping. I found companies that could take all the bitumen off but it would have cost a tidy sum. I used Lecol 5500. But the sides and tongues still needed to be cleaned in order to get a good fit. 2. If the tongues are damaged the blocks can still be used. You could actually take them all off and still have a good finish. I wasn't going to do that to close to 3000 blocks. Again, I found companies that would do this. 3. Spend some time grading the blocks - size, height, wear, complete (tongue). It really does help when laying, and therefore sanding and the finish, as you then don't have huge amounts to level out. Surface 1. Ensure you have a sound subfloor. Luckily I already had one but had to still take it up as I put some sound proofing down under. 2. Make sure level with no screw heads locking out and no squeaks as the last thing you want is to lay it and the floor squeaks all about. Laying 1. Measure, check and double check. Including borders and expansion gap. 2. As shown in the videos lay a crown line: The centre of the room is the backbone of the whole floor, it ensure rows are straight going forward. 3. Start early, especially if you think you can do it in one day. I took a week, doing some everyday after work. But this helped as the previous rows were then hard and didn't move. The adhesive will be a bit slippy and moveable until it's dry so don't walk on it. 4. Lay each row 'dry' to ensure that they will sit together before applying the adhesive. It takes longer and maybe a little messy ( adhesive overlay ) but worth it. 5. For the border, overlay where you've measured where the border should be (making sure not to add adhesive over your marking ) and then use the saw to take off the excess. As it wouldn't have had the adhesive on it'll come up super easy and leave with a clean finish. Sanding, Filling and finishing. 1. If sanding yourself find a firm that has a Trio and belt sander. Absolutely brilliant machines. As they have three rotational disks perfect for parquet as difficult to sand along the grain with belt sander. I used the belt first until the 60 paper grade and then switched to the Trio. 2. Use 60 or 80 dust mixed with resin for filling. Again loads of videos on the Tube. I used Lecol 7500 resin. I filled it twice sanding in between. 3. Research the finish you want and if not sure take an example to a wood flooring specialist to get their advice.
...See More
Can I restore this parquet flooring?
Q
Comments (2)
hi Elizabeth, The floor that you have is nice and is laid with an integral backing from your photos. it is thin as the pattern is small and it is an overlay floor, using the substrate for the strength. you can certainly lift the floor and relay it in a room of your choice. with time and patience I'm sure you will be able to restore the floor yourself, if this is something you want to do yourself. the original floorboards will be ok underneath the parquet, although they may require sanding to remove residual glue. you will need a slight transition strip at the door to get you down to the existing floor height, but it will look fine. it may be worth getting a flooring company to give you a quote for the sanding as this can be a challenge. good luck and enjoy your new home!! best Rowland
...See More
Hall and stairs and a parquet floor.
Q
Comments (7)
If it's dark wood... it's dark wood. It's nice to preserve an original feature but sometimes it just doesn't work anymore so it's time to update. If it was a mistake to use such a dark floor in a dark hall you shouldn't have to live with that mistake just because it's old. Option 1. Remove it and use it elsewhere in the house. Some of it can be used to make furniture or a wall feature. Replace with light floor of your choice. Option 2. Leave it as an original feature but cover over it with a new floor. Laminate / carpet etc. It's always there in case you want to bring it up again at a later date. Option 3. Use stain on it as required and accept that it's a dark floor. Use light paint on the wall and a large runner down the middle to cover enough of it so it doesn't have as much impact. Think of other ways to brighten up the hall e.g. increase the glazing in the front door or the door into the kitchen, remove the small wall next to the kitchen door and replace that with a glass panel, use mirrors, add artificial lighting etc.
...See More

Parquet flooring

Comment (1)

AMARI

Related Discussions

COMPANY

BUSINESS SERVICES

GET HELP

CONNECT WITH US