Fixing open timber cladding fins
James
6 years ago
Hi, I'm looking to replicate the attached image of timber fins. But it's not clear how the face timber is joined to the black battens behind.
I cannot see any screws or nails through the front of the timber.
Does anyone have any suggestions?
Thanks
I cannot see any screws or nails through the front of the timber.
Does anyone have any suggestions?
Thanks
Featured Answer
Sort by:Oldest
Comments (8)
Kerry Donnelly
6 years agoRelated Discussions
60s townhouse exterior dilemma...
Comments (17)One has to question what is going on here, as you appear to feel your house does not make a 'good enough' statement? My first reaction to the exterior was to recoil at the rather 'pushy' cars parked outside, plus the tragic pvc door and weatherboarding! Apart from that the house looks to be quite a sensible, space-efficient design with the reduced heat losses that a terrace brings... Your house is not an individual, but is part of a row of three or even more, meaning that anything you do should take into account the others, be sympathetic and integrate with them. My attitude as a sustainable design consultant would be to only spend money on things that really need upgrading, and only do that with the greatest care so that you do not harm the structure and take into account condensation risk etc. Think carefully about the effect all your changes will make to heat loss and your space heating requirements! Also consider any possible overheating via glazing and be aware that glass has one of the highest carbon footprints while insulation is really low. Remember that every penny you spend earning money comes with an environmental footprint, and when you spend this money you then add a further environmental impact! The obvious areas which could be improved are wall insulation, glazing, doors and air-tightness. Any new glazing should be designed to give really low whole-window U values and should use warm-edge spacers. For me PVC is out of the question as it is rubbish, looks tacky and reduces glazing area. If you are using timber, then look into using Accoya, douglas fir or oak. Velfac certainly make quality windows and doors, but it would be better if all the houses installed them to keep the facade consistent. Thermally broken Nordan, SAS Pure, Aluprof slimline are other windows/doors to check out. If the weatherboarding is to be replaced, then I would advise using Marley Eternit Cedral or Cedral Click (Cembrit also offer a pressed cement board) which will never rot, but again, consider getting your neighbours to join in). You can paint this yourself with Dulux weathershield. Most cedar cladding looks awful once the UV light starts to break it down and the rain gets in. To me, the way we live our lives on the planet is much more important than the way things 'look'. People are exploited by the fashion and interior design companies into spending money on short-term whims and froth which all impact on the resources the planet creates for us. That is not to say that good design is unimportant -take a Harry Bertoia chair for instance - classics that just go on for ever. My motto is KEEP IT SIMPLE & SUSTAINABLE - QUALITY RATHER THAN QUANTITY. Hope this is helpful....See MoreLooking for someone who can design and build workshop shed
Comments (9)Nice Tractor shed ! Normally when constructing wooden wall, you would just create the openings in the frame for the windows and doors out of the same timber as you go by changing the postition and length of the noggins. You don't buy frames for the windows as they just screw to the wood. Door frames are easily ordered off the internet, so when you're doing the construction, know in advance what size windows and door frames you want. The challenge is the roof construction as it needs to be sound and the whole building will likely need to comply with building regs, therefore, i'd suggest that unless you can design this to comply with building regs yourself, then you'd need a structural engineer to do it for you. You need allsorts of different sized timbers for different points on the building and roof, so best to either find one that you can order from the net and amend a little or get the structural engineer to tell you what you need. ( he would do that anyway on his plan ) Plans too are often available off the internet, but you pay for the service as it's a skilled and time consuming job. If you're not happy with all of the construction yourself, then i'd still suggest a good carpenter. I'm sure you can find one that will be happy for you to work along side and not just take over, as i get the impression that's what you'd like. I've done the same for some customers. However, you must be prepared for the fact, that you may slow him down and time is money ( no offence, I don't know your abilities with regards building construction ! ) Here's a good guide for planning permission etc on Timber framed buildings Timber frames There are some wonderful buildings on here that may suit, or the carpenter could amend :- Warwick Garages As for the Sheet cladding :- It's a specialist fit job really as there are all sorts of bits and bobs you need to bolt them together and then to make the roof ridge. You would be best to use a site like 'My Builder' to find a specialist in your area that can do it for you. Again, with this, you need to find out the sizes of the sheet materials available before you can plan for the roof timbers because, the sheets come in particular sizes, the roof timbers need to be the right distance apart to bolt to the timbers without the need to cut each one to size with an angle grinder. Here's and example of sheet cladding suppliers Steel roof sheets It all sounds very complicated I know, to people that build stuff all the time it's not that bad, you just need to know an awful lot if you're going to start from scratch and not buy pre-fabricated. Hope this has all helps. I wish you bags of luck with your project, it sounds very exciting. Get a structural engineer and chippy on board to help you and you'll be fine!...See MoreWindow colour and cladding ideas needed!!
Comments (23)I have had lots of nice comments on my house. Thanks everyone. I would add that I love the 1970's houses the big windows and open concept groovy style. However, the technology to pull it off wasn't quite there when they were built. If you are updating a 1970's house think about how you can introduce more insulation. I did the following: - internally insulated external walls with 10cm of wool. - insulated between floors (keeps things warm and prevents sound) - installed triple glazing and insulated behind the cladding. My heating bills are now minimal...See MoreFixed Glass Windows / Wall Curtain
Comments (4)Hi Billy, Curtain walling is primarily a commercial product, and priced accordingly, so a bespoke design in floor-to-ceiling aluminium frame fixed windows would save considerable money for you. We would recommend a slim or heritage aluminium system to achieve this, although several other systems are possible contenders. The Rationel Windows we sell are especially good (see photos) and can offer aluminium clad timber to provide a lovely warm timber frame inside, and a weather beating maintenance free aluminium outer frame. You could of course look at Crittall steel windows to provide a wonderful industrial style look... Your original example photos show a set of frameless bonded windows, to give a complete wall of glass, whilst the other shows framed windows with possibly some openers at floor level, so clearly there is scope for design variations. A local glazing firm should be able to help suggest some products and designs for you, but if you want to contact us we would be very happy to advise and find you the right solution. YES Glazing Solutions...See More
PROIkonografik Design
6 years ago
James
6 years agoJames
6 years agoKerry Donnelly
6 years agoKerry Donnelly
6 years ago
Gary Morin
3 years ago
Holloways