flat roof extension edge & guttering...
Tani H-S
5 years ago
Featured Answer
Sort by:Oldest
Comments (7)
User
5 years agoTani H-S
5 years agoRelated Discussions
Flat Roof Balcony Fiasco
Comments (12)Hi - been there done that! Start again! OK I can see there is enough clearance below the door to allow a decent fall to be created if its not enough already. This can be done using pressure treated timber firings which are essentially lengths of timber cut and tapered to dimensions according to a plan such as my example below (I realise your balcony is much smaller but you should get the idea). My firrings plan and cutting list shows 3 drain points with the firrings mitred to created falls toward relevant drain. Your local timber supplier should be happy to cut these and pressure treat resulting tapered timbers which would be fixed at 300 centres max and would have 20mm min marine plywood screwed on to them at 150mm centres. OSB 3 roofing 'chipboard' which can come in tongue and groove form would also work, I just prefer ply. They need to be planned out so that the fall of the timber firrings sends any water toward the drainage channel (if there isn't one then create one) or to the edge of your balcony where the rainwater gutter will collect it. Then use RESITRIX - we used this supplier, but there are plenty out there.... http://www.rubber4roofs.co.uk/shop/epdm-rubber-roofing which is a much stro nger version of EDPM rubber and can withstand foot traffic as it is reinforced with fabric making it almost like a wet suit - its a fantastic quality product believe me!. You paint on a black primer on to the ply, then peel the backing off the RESITRIX and apply. Be warned - as experienced people (but not exactly specialist roofers) we managed to do this very effectively, but found that extreme care is needed before committing as once the RESITRIX makes contact its sticks forever!! this is especially difficult at internal corners. Only peel back the backing plastic off the RESITRIX rubber a little at a time as you need to hold it up off the deck to ensure it doesn't make contact in wrong place. two pairs of hands can help!!If you have planned the falls correctly so that the water is sent to the drain, you will now have that long awaited water tight balcony! Now Google 'tiles for decks and balconies' and you will find no end of options of special porcelain or ceramic tiles with plastic adjustable feet for each corner of tile which allow you to place the feet and tiles level on top of your RESITRIX flat roof with no risk of penetration pif the rubber. Water goes between the tiles as they are not grouted, just placed on the feet. Not sure if the tiles you have will work without cracking - you could test this by standing on one which is supported only at corners. by the way RESITRIX happens to be one of a range of flat roof solution I have used including Kemper liquid rubber system (which is reinforced by a fleece like fabric which is simply rolled out onto a bed of liquid rubber then soaked on top with more rubber) Messy but effective, a similar process to GRP. Have also used one piece EDPM rubber which a very competent DIY'er can fit. A very economical and speedy solution, but not good for foot traffic - although they are starting to introduce reinforced versions. We are actually going to use slate grey plastic/wood composite decking http://www.wpc-decking.co.uk To do this we will PLACE a new set of firrings on top of the completed rubber deck but also will stick strips of RESITRIX to underside of firings for protection. now we will have a deck that can be lifted for maintenance in future if required. These firrings are the opposite of the ones used to create the falls, which brings the deck back to level of course! In reality we will actually adjust to maintain a slight fall so that, and the gaps in the deck takes water away. A long answer - I hope that it helps! Best of luck! Nick Wall Design + Build 07745581167...See MoreFlat pitched roof or flat roof with parapet?
Comments (7)200mm has ruined your kitchen? Sounds like a very important 200mm. Why don't you just move the worktop out by 200mm? Standard worktops are 600mm so not sure where the 800mm came from. Could do a parapet, just on the neighbours side or all the way round? Will have to be weatherproofed with a lead or similar parapet internal gutter + chute / hole in the wall to get water out + damp proof cavity trays above gutter. A parapet may not look as nice unless it was detailed nicely. Could add on a few thousand £ depending on height and length of parapet and materials used....See Morehidden gutter dilemma
Comments (1)There are different ones you can get where they sit behind the fascia board so shouldn’t effect your actual roof. Someone on here might know. We looked into it as got a similar extension but ended up having the front of the fibreglass roof painted black with black guttering and you barely notice it. Thought it would look awful on show but it doesn’t....See MoreSmart sun shading solutions for South-facing extension
Comments (5)We're building a Passive house and are debating about brise soleil at the moment to shade the downstairs rooms. We live in Cumbria so similar to you it's only going to be necessary for 2-3 months a year, so nothing too intrusive/ugly. There are some good examples out there, but it's about knowing what to look for. You might find that it doesn't need to be as wide as you think - only enough to block the sun at its highest couple of hours in the day, and then in winter when the sun is lower you still get the light in...See MoreUser
5 years agoIkonografik Design
5 years agolast modified: 5 years agominipie
5 years agoTani H-S
5 years ago
Ikonografik Design