Help! Glazing to entrance
sugarbowl17
2 years ago
Featured Answer
Sort by:Oldest
Comments (17)
Akira Yamanaka Architects
2 years agosugarbowl17
2 years agoRelated Discussions
Help with corner glazing in extension plans
Comments (6)Hi, We had a feature corner window in our design. Originally it was meant to be a custom glass unit just as the one shown with a cantilever beam. However, the cost of the glazing ate into our budget and would have compromised on something else. Anyway, we went for two separate standard units with a corner post (take a bit of weight but more to join the units together). This worked out much cheaper and still gave us the finish we are happy with. Think it was around £1450 compared to quoted prices of £5000-6000. The builder was reluctant also, but if its in the plans (steel calculations) and they have quoted for it then there should be no issue!. Just having a second look at your plans, the one I would be worried about is the run of glazing (opposite your patio doors). A cantilever beam needs to be much more than the length of the run you are showing from what I understand of engineering. So not sure how they architect/structural engineer have accounted for that!....from my experience. Architects can sometimes get carried away with a design without thought about such practicalities. I would go back and question this design element...Builders vs architects!...See Moreglazed hallway door help!
Comments (5)I am guessing you need the door and window in situ as the porch extension is not insulated. I think all the red brick inside the porch make it look dark when looking out through window/door so you could either paint the brick a lighter colour or plaster board and paint over the brickwork which would give you a level of insulation as well. This will give you a lighter aspect. You could then change the door from hallway to porch to something more modern like the oak and glass internal door on the other pic. Then look to change the window configuration to a one piece of plain or obscured glass removing the little opener as it looks wrong on an internal window....See MoreDESIGN HELP FOR ENTRANCE/BOOT ROOM
Comments (3)I think if you clad it with boards placed horizontally that do not have joints like normal tongue and groove I.e they butt up against each other neatly they will look modern in style. I would consider a layer of insulation underneath them as this area looks like it might not have any. I think you could fit in a narrow u shaped bench with shoe storage underneath or just on 2 sides as suggested above. Maybe get a carpenter to quote they will be able to draw up options for you....See MoreHelp! Small entrance hall ideas
Comments (37)Guys, I need more advice! 😕 I had planned on using wall panelling on the right hand side of my stairs, but I have pulled off a piece of wood that ran the length of the stairs and it's a bit of a mess underneath. I'm now thinking the normal batten style panelling is out of the question as I'm not going to get a straight wall once I've tarted up what's underneath where the wood was. Anybody got any ideas on how I can design this part of the stairs now? I believe the wood was placed there to cover where a previous handrail had been. It's quite low down tho, so must have been placed there by a fairly small person! I like the idea of tongue and groove panelling to basically cover the detritus that's been left, but I've no idea how to work out the angle to cut it to the correct size all the way up the stairs. So thinking of maybe just replacing the wood that was there with a fresh piece, maybe with a dado on top. Oh I don't know, help! Plans have been kiboshed! 🙈...See MorePeter
2 years agoAkira Yamanaka Architects
2 years agosugarbowl17
2 years agosugarbowl17
2 years agosugarbowl17
2 years agoAkira Yamanaka Architects
2 years agosugarbowl17
2 years agosugarbowl17
2 years agosugarbowl17
2 years agoPeter
2 years agoAkira Yamanaka Architects
2 years agoWumi
2 years agosugarbowl17
2 years agogemmilln
2 years ago
arc3d