How to get architraves smooth before painting?
last year
last modified: last year
Featured Answer
Sort by:Oldest
Comments (10)
Related Discussions
(another) HALLWAY painting post
Comments (110)Thank you all very much for your compliments and also encouragement to take a walk on the complete dark side (instead of whimping out! Ha ha) @Beano - the lights as they are in the main hall are very low level but once I have the shades on and swap the bright bulbs out, it won’t be as blinding. The entrance hall one is bright and a sensor one and I think that helps push light over to the darker side. It can be turned off though. Not decided yet on artwork ie if I should go eclectic frames or clean modern... I’m a fan of both so 🤷♀️...See MoreOpinions on painting or not painting this dark wood?
Comments (15)HI Gina, Definitely paint it out - doors, windows and stairs (leave handrail dark to contrast ). I spent 10 years at our previous 1930's house debating whether to paint the original bannisters which had been varnished by previous owners. Prep it all well - sand and clean and prime or you may get away with no sanding and use Zinsser B-I-N primer. I used white eggshell on bannisters and stained the handrails dark. I also painted the hall and landing walls/ceiling in Pavilion Grey (valspar colour match) and white. I can't tell you what a difference it made to the brightness and feel of the area and we already had big stained glass front door and long window on the stairs but the colour scheme really brightened it up. Will try to add photos.. Good luck. BTW we've recently moved to an 1830's weavers house and its dark, dark, wood EVERYWHERE!! Lots more painting to hone my skills..!...See MoreSmoothing textured ceiling
Comments (12)It totally depends on how "well" the artex was first installed. My parents house used to have artex ceilings in every room! I took them down quite easily with a steamer and scrapper. They had almost perfectly smooth ceilings underneath. A bit of filling and sanding two-three coats of paint and job done. There were some spots though that had been re-artexed at some point and they were very difficult to remove. the steamer had no effect on them so it took a lot of soaking, scrapping, filling and sanding to get those bits right. Thankfully that was only a handful of areas. I saw a decorator once paint an artexed ceiling. He stepped outside for a break once he had done one coat. I was in an adjoining room and thought I could hear water dripping. Stepped in the room to see strips of artex just peeling right off and falling to the ground. He scrapped of the remaining bits and then painted. End result was better than anyone was expecting! So in summary if the artex was of poor quality and the ceiling was poorly prepared when it was applied, it will come of very easily. If on the other hand they did a proper job then its cheaper and quicker to plasterboard over it and start again....See Morehow to prep this wall for painting
Comments (11)Don’t worry too much about the cost of plasterboard it’s about £7 a sheet and standard size is 2.4m tall and 1.2m wide so you can work out the cost to renew the whole room or just the bad bits (I bet you don’t need to do it all) plus they’d either use battens to fix to the wall, again cheap just lengths of timber screwed into your existing brick walls or dot and dab where they use big blobs of adhesive to stick the plasterboard to the wall. Get a few local well rated plasterers in to give you a price and you will know exactly where you are with it. Better still get a recommendation from a friend. Also the tearing out of the room may save you a bit of cost so ask for a price to do it with them doing the demolition or you doing it yourself it’s really easy to do and might save a few pounds. I’ve popped a pic on of some of my old house I stripped completely, it’s easy if a bit messy!...See More- last year
- last year
- last year
- last yearlast modified: last year
- last year
- last year
Juliet Docherty