Porthole window internal poor finish
HU-539016709
last year
last modified: last year
We have a round porthole window and it’s been finished internally poorly. Looks to have plywood surround fitted. I’ve asked a couple of handy men for
ideas. One said to even it out with wood filler or a repair plaster filler. Another to fit some hardboard and plaster up to it. I think I should remove the plywood and plaster but not sure what I’ll find underneath!
Featured Answer
Sort by:Oldest
Comments (7)
Jonathan
last yearRelated Discussions
Parquet floor disaster? Help
Comments (166)Those are wise words Karen! am so glad it worked out for you. Love to see a photo, what colour or shade did you choose? Jools, The bitumen is a right pig, best way we found is to make it cold, so it becomes brittle, then you can scrape /chip it off. We used a window scraper, coarse wire wool and various sandpaper. We left the window open on a cold night, turned heating off in there, and you could try a cooler fan on it. Putting ice bags on it didn't work as well as we hoped. we used a round sander, but it can cause swirls, it's really awkward ! To be honest a few dips and scratches on an old floor are okay in the end, don't be too afraid of it, they are only pieces of wood stuck down on the floor, not bone china, as long as you try not to break them, or set fire to them, otherwise you can't possibly do more damage than I did, and they recovered!...See More1930's House facelift help please
Comments (29)Hey So the latest update is that we're still busy with the project but in the closing stages. We've done a lot of work inside more than originally planned we've gutted the house and replaced everything and changed the floor plan to modernise it and make more of an open plan space downstairs. We've done the rear extension which is now dedicated to kitchen with a central island running parallel with the doors . On the outside the house has had external insulation fitted and new render which makes it look new. I've attached some recent pics. Richard...See MoreVictorian Renovation in London - Part 2
Comments (201)Thanks guys - we did a lot of experimenting and testing on some old floorboards before deciding on this stuff. The Osmo oil gives a deep and rich finish on old pitch pine that looks very different to varnish - deeper and with more of the grain being brought out. It's more like a beeswax finish from olden times, without the backbreaking labour and maintenance. Interestingly on the new boards (in the top bedroom), it makes far less difference: the new pine just looks yellow and shiny, much as it would if varnished. But the oil should be tougher and lower maintenance. We decided to restore these floors rather than replace as they were actually in remarkably good condition: this house has never had fitted carpets fitted, nor central heating fitted until 2014, and when it was installed it was installed with regard to keeping the floors intact (many systems installed in past decades saw the boards sawn up and hacked about). I wanted look that is obviously original, and can't be mistaken for engineered wood. I did think about a limewashed finish, but bottled it at the last minute and went totally traditional, as I thought less risk of a finish done to a trend that would be hard to reverse....See MoreKitchen/diner extension layout suggestions
Comments (19)So I just went outside to actually measure the full width of the house, the estate agent plans from when we bought said it's 5m wide so I was quite surprised to find its actually 5.65m and we can extend a further 50cm out so a total external width of 6.15m. Even subtracting the wall thicknesses there's more room to play with than I had originally realised! Have been fiddling with the plan. If I were to lose the raised oven and possibly the pantry the design does look more open and means I could have some open shelving too. Its just whether that ends up being form over function in terms of how I use a kitchen. Hmm decisions decisions! Thanks again for all the help though - much appreciated!...See MoreHU-539016709
last yearUser
last yearHU-539016709
last yearThanks like the look of the jackoboardrcd. Probably the 3mm one. can i stick it in place with sticky foam or something more specialised?
PROCaldicot Kitchen & Bathroom Centre
last year
Caldicot Kitchen & Bathroom Centre